← Back to 3D Models
ORCA SLICER WORKFLOW

3D Printing Guide

A practical, illustrated workflow based on a real multi-part bust sliced in Orca Slicer. The screenshots show exactly where the main controls are and which values were tested in this example. Use them as a starting point, then validate the final slice for your own printer, filament and model size.

Tested example — not a universal preset

Creality CR-10 · 0.4 mm nozzle · Generic PLA · 0.16 mm layer height. Different printers, filaments, nozzle sizes and model scales may require different values.

Quick reference: example profile

These are the values used for this specific test. They are a practical baseline, not mandatory settings for every model.

SettingExample valueWhy it matters
Printer Creality CR-10 Example machine used for this guide
Nozzle 0.4 mm Standard nozzle used for the test
Material Generic PLA Tune temperatures for your own PLA
Layer height 0.16 mm Good balance between detail and print time
First layer 0.20 mm at 15 mm/s Slow first layer to help adhesion
Walls 3 perimeters Adds shell strength without excessive material
Infill 5% Gyroid Suitable starting point for a decorative bust
Temperature 220 °C nozzle / 55 °C bed Tested values for this PLA profile
Brim Auto · 5 mm · 0.1 mm gap Useful when extra bed adhesion is needed
Supports Normal (auto) in this test Used less material and time than Tree (auto)
STEP 1

1. Check the package files before slicing

A downloadable model can contain separate files for the bust, pedestal and accessories. Check every component before you start changing print settings so you know which parts must fit together after printing.

  1. Load each model file and confirm which part it represents.
  2. Keep fitting parts at the same scale percentage unless the product instructions explicitly say otherwise.
  3. Accessories such as glasses may need a different print orientation even when their scale must stay matched to the bust.
  4. Confirm that no file is missing before starting a long print.
STEP 2

2. Verify scale and orientation

Before changing quality or supports, confirm the real dimensions of the model. Uniform scaling protects the proportions and helps separate parts continue to fit correctly.

  1. Select the object and open Scale.
  2. Keep Uniform Scale enabled unless you intentionally need to distort one axis.
  3. In this example the bust is 108.89 mm high at 100% scale.
  4. If you change the bust scale, apply the exact same percentage to the pedestal and fitting accessories.
  5. Open Rotate and check X, Y and Z. Keep the intended base/contact surface correctly positioned on the build plate.
STEP 3

3. Set print quality, strength and speed

For a decorative bust, the goal is usually to preserve facial and surface detail without adding unnecessary print time or internal material. The values below are the tested starting point used for this example.

  1. Layer height: 0.16 mm. First layer: 0.20 mm.
  2. Walls: 3 perimeters.
  3. Top shell: 5 layers / 1 mm. Bottom shell: 4 layers.
  4. Sparse infill: 5% Gyroid.
  5. First-layer speed: 15 mm/s.
  6. External wall: 35 mm/s. Internal wall: 60 mm/s. Sparse infill: 70 mm/s. Top surface: 30 mm/s.
  7. For smaller busts or very fine details, a lower layer height can improve detail but increases print time.
STEP 4

4. Check PLA temperature and cooling

Temperature and cooling affect surface quality, overhangs, bridges and layer bonding. Use the filament manufacturer range as a starting point and fine-tune it for your own printer and PLA.

  1. Tested nozzle temperature: 220 °C for the first and following layers.
  2. Tested bed temperature: 55 °C for the first and following layers.
  3. Flow ratio in this profile: 0.98.
  4. Cooling fan: 100% in the shown profile, with extra cooling enabled for overhangs and bridges.
  5. If your PLA shows poor layer bonding, excessive stringing or weak overhangs, tune temperature and cooling instead of copying the example blindly.
STEP 5

5. Improve bed adhesion when needed

A brim can help narrow, tall or uneven parts stay attached to the build plate. Use it when the model footprint or your first-layer conditions make adhesion uncertain.

  1. Example Brim setting: Auto.
  2. Example width: 5 mm.
  3. Example object gap: 0.1 mm.
  4. Clean the build surface before printing and verify first-layer calibration.
  5. Do not add a large brim automatically if the part already has a wide, stable contact area.
STEP 6

6. Compare supports before choosing them

Support type should be chosen from the sliced result, not from a rule such as “Tree is always better.” In this test, Normal automatic supports were both faster and lighter than Tree automatic supports.

  1. Slice once with Normal (auto) and inspect where supports touch the face, hair, clothing and shoulders.
  2. Slice again with Tree (auto) if you want to compare contact areas and removability.
  3. Compare estimated support material and total print time.
  4. If automatic supports touch delicate facial details unnecessarily, experienced users can switch to manual support placement.
  5. Printing with no supports is only appropriate when the preview confirms that every required region can print safely.

Support comparison from this test

Support modeMaterialTimeResult
No supports 45.63 g 6 h 04 min Floating-region warning — verify carefully before printing
Normal (auto) 54.76 g 8 h 28 min Best starting point in this specific comparison
Tree (auto) 61.03 g 10 h 21 min More material and longer print time in this model

The no-support slice is included only as a comparison. Orca Slicer warned about floating regions, so the shortest time is not automatically the safest print choice.

STEP 7

7. Inspect the sliced preview before exporting G-code

The preview is the final safety check before a long print. Do not rely only on the 3D model view: inspect the actual generated toolpaths and the estimated material/time.

  1. Move through the layer slider and look for floating islands or regions that begin in mid-air.
  2. Check the underside of the chin, nose, ears, hair, shoulders and any accessory attachment points.
  3. Look for unexpected gaps, extremely thin features or support contact on important visible details.
  4. Check total filament and estimated time before exporting G-code.
  5. After starting the real print, watch the first layers and stop the job if adhesion or extrusion is clearly wrong.

Before you print

Always validate the model in your slicer before printing. Orientation, supports, temperature, cooling, speed, infill and adhesion can change with printer, nozzle, material, model geometry and final scale. If a package contains separate fitting parts, apply the same scale factor to all fitting parts unless the product instructions explicitly say otherwise. The values in this guide are examples from one tested workflow and are not guaranteed settings for every machine.